|
|
|
|
|
|
|
|
3/16" Aluminum Slip Tank
This aluminum tank has: - dimensions of 48" long X 20"wide X 12"tall. - constructed out of 3/16" aluminum plate - TIG welded seams - (2) 2" NPT collars for fill neck/pump/vented cap. - 1/2" NPT ...
|
$800.00
|
|
|
|
|
|
|
OIL PRESSURE SENSOR 5.3
I have an oil pressure sending unit from an '06 Sierra with a 5.3. Will fit all 4.8/5.3/6.0 engines with the single pin connection. Will likely fit many other GM applications. I'm selling it because ...
|
$20.00
|
< 1 hour ago
|
|
|
|
Wanted:
Jeep engine
4 litre 6 inline engine.
|
$600.00
|
< 6 hours ago
|
|
|
|
Nissan KA24 cylinder head
Taken off a 1990 240SX with 80,000km. Bought it to replace the head on my car but the car was totaled by a careless driver before I got around to it.
|
$60.00
|
< 8 hours ago
|
|
|
|
2000 honda civic si for sale or to part out
I have a 2000 Honda civic si it has aprox 137 000 km on it and was in a crash on the passenger side was hoping to sell car for parts car or to part out as much of it as possible I just put brand new ...
|
please contact
|
< 9 hours ago
|
|
|
|
Ford 5.0 litre with transmission
Ford 5.0 from 1991 ford 4x4. engine complete with transmission and transfer case approx 50,000 km on motor, 30,000 km on transmission
|
$1,200.00
|
< 10 hours ago
|
|
|
|
AUTOMATIC BELT TENSIONER FOR '02-'09 HONDA CRV
DAYCO AUTOMATIC BELT TENSIONER FOR '02-'09 HONDA CRV, made of cast aluminum. Bought in the US for my '05 CRV, but not needed. NEW & still in box. Cost of tensioner at Honda dealer aprox $220. ...
|
$50.00
|
< 10 hours ago
|
|
|
|
CATALYTIC CONVERTER for '05 HONDA CRV
MAGNAFLOW DIRECT FIT CATALYTIC CONVERTER - 3-bolt flange inlet, flange outlet. Single inlet and outlet configuration, with oxygen sensor ports. Includes stainless steel heat shield. Ceramic honeycomb ...
|
$350.00
|
< 10 hours ago
|
|
|
|
355 chevy unassembled
high nickel block 305 ported heads with new valve seals and seats. hp 350 cam edelbrock intake and carb "new" Holley electric fuel pump "new" distributor factory new cap, rotor and wires new piston ...
|
please contact
|
< 11 hours ago
|
|
|
|
Stock cast iron 454 intake
Stock cast iron 454 intake Painted Chevy orange. $25
|
$25.00
|
< 13 hours ago
|
|
|
|
GET NOTICED!!!! With some LOUD exhaust for your 12v dodge
Exhaust came off a 98 12v, should fit any Dodge Cummins from 94-02. It consists of a newer 4" down pipe and 5" pipe all the way to exit in front of the right rear wheel. This exhaust is LOUD, rattles ...
|
swap / trade
|
< 14 hours ago
|
|
|
|
|
m--QTBPoBt0EL5w~~48_14.JPG)
|
1.6L VW Diesel motor non turbo
I have a 1.6L diesel out of a 1991 Jetta, was runnung good when pulled. $350.
|
$300.00
|
< 14 hours ago
|
|
|
|
355 ENGINE AND 350 TRANNY PUSHING 500 HP
ALIUMINUM HEADS ITS A FAST AND POWERFUL ENGINE WITH LESS THAN 2000 MILES ON IT COMES WITH HEADERS I HAVE NOTHING TO PUT IT IN SO I GUESS ITS FORSALE OR TRADE ITS OUT OF MY 1972 NOVA
|
swap / trade
|
< 16 hours ago
|
|
|
|
Ford starter
New starter for 7.3l diesel
|
$200.00
|
< 17 hours ago
|
|
|
|
Wanted:
WANTED 1600cc Volkswagen aircooled engine or any misc parts
Looking for any volkswagen aircooled parts Engines,Trans . Bodys complete or not will pay cash 403 350-4056 Todd
|
please contact
|
< 18 hours ago
|
|
|
3BPvww)s0Mg~~48_14.JPG)
|
EDELBROCK PERFORMER SERIES 600 CFM, ELECTRIC CHOKE CARBURETOR
EDELBROCK PERFORMER SERIES 600 CFM, ELECTRIC CHOKE CARBURETOR. Part number #1406. I bought it new few months ago an its to small for my 390. It ran on the motor for a day or 2 then relized the bottom ...
|
$350.00
|
24-May-12
|
|
|
|
Chevy Small Block 400 #3951511 4 bolt mains
I have a Chevy small block 400 for sale, casting number 3951511 with the 4 bolt mains. Came from a 1971 truck, and has not been machined, still in original condition. Not sure the mileage on the ...
|
$250.00
|
24-May-12
|
|
|
|
Starter for ford 7.3l diesel
Brand new starter for 7.3l diesel motor
This ad was posted with the Kijiji Classifieds app.
|
$200.00
|
24-May-12
|
|
|
|
7.3 l ford starter
brand new starter for ford 7.3l diesel
|
$200.00
|
24-May-12
|
|
|
|
Aluminum intake manifold ( Chevy 350 )
Used factory aluminum intake manifold off a 1981 Camaro Corvette 350 engine. Part # 14014432. Asking $50. Email or call 403-596-1056. Thanks
|
$50.00
|
24-May-12
|
|
|
|
E34 BMW M5 Pulse Generator #12121311710
This unit fits on the number 6 plug wire of the BMW E34 M5. They are known to break easily after time. I replaced the part, and then found I needed a complete new plug set which included the pulse ...
|
$115.00
|
24-May-12
|
Post your classified or want ad in this category. It's fast, easy and free.
Visit us on our Blog
Download our iOS App
Friend us on Facebook
Watch us on YouTube
Follow us on Twitter